New York City Subway chaining
Encyclopedia : N : NE : NEW : New York City Subway chaining
In the U.S., chaining is a method by which railroads precisely measure and specify locations along the line. It measures distances from a fixed point, called chaining zero, following the twists and turns of the railroad line, so that the distance described is understood to be the "railroad distance," not the distance by the most direct route ("as the crow flies").
This article describes chaining on the New York City Subway system, where each "chain" is 100 feet (~30.5 m) long. This is as opposed to the milepost or mileage system, where distances are usually measured in miles and hundredths.
Chaining zero
Chaining zero is a fixed point from which the chaining is measured on a particular chaining line. A chaining number at a specific location (called a chaining station) on a line of 243, say, identifies that the point is 24,300 feet (~4.6 miles or ~7.4 km) from chaining zero, usually measured along the center line of the railroad.Once chaining is established, it is rare but not unheard of to change the location of chaining zero or the route along which it is measured on a given line. There are several examples of chaining numbers to refer to a chaining zero location that no longer exists or along a physical line that no longer exists, because of abandonment or demolition. Notable among these are several existing chaining lines that originated near New York City Hall via the Brooklyn Bridge, discontinued since 1944. It is very rare but not impossible for a reroute to alter the accuracy of chaining numbers, if only slightly.
Exceptions exist to the principle that chaining numbers represent a railroad distance to the zero point. On the original IND chaining zero for the original system is a political rather than physical location, and there is no railroad at or near the zero point. Sometimes trackage (usually but not always short distances) is chained backwards from a tie point with another line.
Chaining lines
Chaining lines are routes on physical railroad lines that are usually described by one or two letters for the purpose of identifying locations on those lines.Chaining lines are not necessarily the same as the physical lines they run on. One physical line may have several chaining letters, and one chaining line may cover several physical lines.
The letters assigned to a chaining line have nothing whatever to do with the letters displayed on trains and public maps and timetables. These latter are subway service letters . See: New York City Subway nomenclature and .
For example, the BMT A chaining line begins at BMT South chaining zero north of 57th Street on the BMT Broadway Line, but is interrupted north of the Canal Street stations, where the express tracks becomes BMT H for the trip over the Manhattan Bridge south side tracks and the local tracks become BMT B for Lower Manhattan and the Montague Street Tunnel. The BMT A line begins again in the middle of the Manhattan Bridge span on the north side tracks, passes through DeKalb Avenue and then becomes the BMT Brighton Line for that line's entire distance to Stillwell Avenue.
Track numbers on chaining lines
Each track on a chaining line is given a number, letter or (rarely) a combination of both to identify a particular track on a particular line.BMT / IND practice
On the BMT and IND an odd numbered mainline track is going railroad south and an even numbered mainline track is going railroad north. In many locations a track may be going "railroad" north or south where the compass direction is different or even opposite. This may be because it is an essentially east-west line (e.g., the Jamaica Line), so railroad north means towards Manhattan and railroad south means away from Manhattan. It may also be because a line continuing from a north-south line turns in another direction (e.g., the IND Fulton Street Line) but the railroad direction remains the same.These track numbers provide a definitive way of determining whether a particular direction on a particular line is going "railroad" north or south. Especially it shows that "south" on several lines (including the BMT Jamaica Line, the IND Fulton Street Line and the BMT Myrtle Avenue Line) that run in an easterly to northerly compass direction for their entire route are nevertheless running railroad south.
The local (usually outside) tracks on a given BMT/IND line are numbered 1 (south) and 2 (north). The express tracks are numbered 3 (south) and 4 (north). If there are an odd number of mainline tracks, the center track is (for example) track 3/4. The signals heading southbound will show the location as track 3 and northbound track 4. Additional tracks on the same chaining line are usually numbered higher by the same rules. On the four track BMT Brighton Line, the tracks from west to east are:
A1 - A3 - A4 - A2On the three track BMT West End Line, they are:
D1 - D3/4 - D2On the two track BMT Canarsie Line, they are:
Q1 - Q2
IRT practice
On the IRT the tracks are numbered differently, the southbound tracks are 4 (local) and 2 (express) and the northbound are 1 (express) and 3 (local). On a four track line, the tracks are numbered:
4 - 2 - 1 - 3On a three track line, M is used for the middle track, and 4 and 3 are still the local tracks:
4 - M - 3And on a two-track line, there are no express tracks, so the two tracks are:
4 - 3Strangely, within stations IRT tracks change chaining numbers; from left to right, tracks number 1 through 4:
1 - 2 - 3 - 4And on a three-track line:
1 - M - 4Thus, a line can run north up to a station as "4-2-1-3" and run through it as "1-2-3-4", or run up to it as "4-M-3" and through it as "1-M-4".
Handling chaining junctions
When one line splits from or joins another, a decision must be made on how to measure the chaining distances on the individual lines. One way is to establish a new zero point for one or more lines, but this is inefficient. Typically a major end-point terminal will be chosen as chaining zero, and all lines that are tributary to that terminal will measure their chaining from that point. This process is called tying. For example, if one line ties to another at a certain point, and the chaining station number at that point is 135+10 (13,510 feet from chaining zero), then a location on either branch that is 1,000 feet from that will have a chaining station number of 145+10.
Tying
When a new line or branch separates from another line, and it is desired to "pick up" the chaining numbers of the original line, the new line is said to be "tied" at that point. For example, where the BMT Montague Street Tunnel Line (BMT B) separates from the Broadway Line (BMT A via the Manhattan Bridge) north of Canal Street and Broadway, we say that BMT B ties to BMT A at Canal and Broadway. That way we know that (assuming BMT A ends at chaining zero, which it does) we measure the distance from a chaining station on BMT B by following the physical BMT B to its tying point, and then following the physical BMT A from there to chaining zero.Reverse tying
Sometimes when a line leaves another line, we want the chaining on the branch line to be tied to the original line, but we want the chaining distances to go down instead of up. This is almost always because the branch joins the main line coming from the same direction as the main line, and we want the chaining numbers of the branch to be derived from the main line, so as not to have to establish a separate chaining zero location for the branch. An example of this was the Fulton Ferry branch of the Fulton Street Elevated (BMT K) which split from the Brooklyn Bridge branch at a location called Kings County (KC) Junction. Chaining zero for both branches was at Park Row, over the Brooklyn Bridge. The stub end branch to Fulton Ferry (the original terminal) was chained backwards from Kings County Junction to the East River shoreline. The chaining numbers went from 0+00 (zero) at the western end of Park Row station to 77+20 (7,720 feet) at KC Junction. Then the Fulton Ferry branch was reverse tied at that point so that the chaining station at the ferry end of the line was 45+38 (4,538 feet). By this method, the distance from any point on the Fulton Street el to either terminal could be readily measured.No tying
Sometimes two or more lines merge or abut but we don't want the chaining to be tied. For example, the Montague Street Tunnel Line BMT B is tied to Broadway Line BMT A at Canal Street, but BMT B returns to BMT A at DeKalb Avenue in Brooklyn. Since BMT B uses a longer route to reach the same location than BMT A does, the chaining numbers are different where the two lines rejoin. In this case, the BMT B chaining simply ends and the BMT A chaining is picked up again.Chaining codes
Following are tables describing the chaining lines of all three divisions, including defunct lines.BMT
Many of these lines originally had individual chaining zero points as a result of the different companies that built and operated them. The BRT consolidated the chaining system subsequent to taking over these and many lines were again rechained when they were shifted from elevated to subway lines. These chaining lines and zero locations are accurate as of c. 1900 for lines chained from Park Row; as they were opened c. 1915–1920 for lines chained from 57th Street; as of line openings for other lines. Where chaining has changed since these chaining lines were established, the current chaining is shown.
| Chaining line | Physical line | North | South | Chaining zero |
|---|---|---|---|---|
| A | Broadway Line / Brighton Line | 57th Street | interlocking south of Prince Street | 57th Street–Seventh Avenue |
| midpoint of Manhattan Bridge north tracks | Stillwell Avenue | |||
| B | Broadway Line / Montague Street Tunnel | Canal Street (ties to BMT A) | junction with Brighton Line south of DeKalb Avenue | |
| C | Culver Line | Ninth Avenue lower level (ties to BMT D) | Fort Hamilton Parkway | |
| D | West End Line | 36th Street (ties to BMT F) | Stillwell Avenue | |
| E | Sea Beach Line | 59th Street (ties to BMT F) | ||
| F | Fourth Avenue Line | Gold Street Interlocking north of DeKalb Avenue (ties to BMT A) | 95th Street | |
| G (tracks 1 and 2) | 60th Street Tunnel / Astoria Line | Ditmars Boulevard | 57th Street–Seventh Avenue | |
| G (tracks 3 and 4) | 63rd Street Line | Lexington Avenue–63rd Street | ||
| GD | 60th Street Tunnel Connection | Queens Plaza | junction with BMT G (1/2) west of Queensboro Plaza (ties to BMT G) | |
| H | Manhattan Bridge south tracks | interlocking south of Prince Street (ties to BMT A) | interlocking north of DeKalb Avenue | Chambers Street
|
| J | Nassau Street Line / Jamaica Line | Chambers Street | 168th Street (demolished) | |
| Jamaica Center | ||||
| K | Fulton Street Line | Fulton Ferry (demolished) (reverse-tied to main BMT K) | Kings County Junction | Park Row |
| Park Row (demolished) | Lefferts Boulevard | |||
| L | Lexington Avenue Line (demolished) | Grand Street/Myrtle Avenue (demolished) (tied to BMT M) | Broadway | |
| M | Myrtle Avenue Line | Sands Street (demolished) (tied to BMT K) | Broadway (abandoned) | |
| Myrtle Avenue | Metropolitan Avenue | |||
| N | Fifth Avenue Line | Myrtle Avenue/Hudson Street (tied to BMT M) | 65th Street/Third Avenue (demolished) | |
| O | Franklin Avenue Line | Franklin Avenue/Fulton Street (ties to BMT K) | Prospect Park | |
| P | Canarsie Line–Linden Yard | Livonia Avenue | Linden Yard | between Atlantic Avenue and Sutter Avenue |
| Q | Canarsie Line | Eighth Avenue | Rockaway Parkway | Eighth Avenue |
| R | Nassau Street Line | Chambers Street | Montague Street Tunnel (reverse-ties to BMT B) | 57th Street–Seventh Avenue |
- BMT C: Original BMT C ran along the entire length of the Culver Line, from the lower level of Ninth Avenue over to Ditmas Avenue (over the right-of-way of the South Brooklyn Railway), then along the McDonald Avenue El to West Eighth Street, where BMT A (Brighton Line) chaining took over. With the opening of the Culver Ramp, the IND acquired the Culver Line from Ditmas Avenue south and rechained it as part of IND B (from 57th Street/Sixth Avenue to West Eighth Street). The surviving portion of the northern Culver Line, which today runs from Ninth Avenue lower level to about [Fort Hamilton Parkway and 37th Street], is still chained BMT C.
- BMT G: Tracks 3 and 4, which constitute the BMT 63rd Street Line, are not to be confused with track G3-4, the single express track on the Astoria Line.
- BMT K: The Fulton Ferry spur was chained from Park Row to Kings County Junction (located east of former Sands Street station), then backwards from the junction to Fulton Ferry.
- BMT L: Lexington Avenue Line chaining ended at the intersection of [Lexington Avenue and Broadway], where the Lexington Avenue Line merged with the Broadway–Brooklyn Line (between Kosciuszko Street and Gates Avenue stations).
- BMT P: Until recently, BMT P consisted of the Canarsie Line from Broadway Junction to Rockaway Parkway. The entire Canarsie Line has since been rechained as BMT Q; the only remaining P chaining is the yard lead that diverges from the main line just south of Livonia Avenue and leads to Linden Yard.
- BMT Q: Until recently, chaining for BMT Q began at Sixth Avenue—the original northern terminal of the 14th Street subway—and continued south to Broadway Junction. South of Broadway Junction, the line was chained as BMT P with chaining zero at the intersection of [Pitkin and Van Sinderen Avenues], where the Canarsie Line had diverged from the former Fulton Street Line. When the 14th Street subway was extended to Eighth Avenue, the new trackage was chained as BMT QW, with chaining starting at Sixth and increasing to Eighth. The Canarsie Line has since been entirely rechained as Q, running from the zero at Eighth Avenue south to Rockaway Parkway.
IND
- IND zero: The zero point of the IND system was determined by extending the centerline of West Fourth Street station south to the New York/New Jersey border. The point of intersection—located in Lower New York Bay just north of Keansburg, New Jersey—was calculated to be 96,925 feet (18.357 statute mi or 29.542 km) from the south ends of the Eighth Avenue Line platforms at West Fourth Street; these points became chaining point 969+25. Chaining distances then increased railroad north of West Fourth and decreased railroad south. As a result the principle that chaining stations along any line reflect the accurate distance to a chaining zero point via the physical railroad is not true on the IND.
- IND F/FA: The Rockaway Line was originally part of the Long Island Rail Road and was chained from Long Island City station in Long Island City, Queens, via the old Montauk Line. When the IND acquired the Rockaway Line south of Liberty Avenue in 1956, it preserved the LIRR chaining distances.
- IND K: The Liberty Avenue Elevated, currently part of the IND Fulton Street Line, was originally the eastern portion of the BMT Fulton Street Line, which had its chaining zero at Park Row. When the IND acquired the Liberty Avenue structure, it preserved the BMT chaining letter and zero point, reverse-tying the chaining back to Euclid Avenue.
IRT
| Chaining line | Physical line | North | South | Chaining zero |
|---|---|---|---|---|
| B | Broadway-Seventh Avenue Line | 96th Street | Times Square–42nd Street (ties to IRT MM) | Brooklyn Bridge–City Hall |
| BB | 242nd Street–Van Cortlandt Park | 96th Street (ties to IRT B) | ||
| C | Flushing Line | Main Street–Flushing | Times Square | |
| D | Nostrand Avenue Line | Franklin Avenue (ties to IRT E) | Flatbush Avenue | Brooklyn Bridge–City Hall |
| E | Eastern Parkway Line | Borough Hall (ties to IRT 3) | New Lots Avenue | |
| F | Lenox Avenue Line / White Plains Road Line | Bronx Park–180th Street | 96th Street (ties to IRT B) | |
| G | Bergen Cutoff (from White Plains Road Line to Third Avenue Line) | Jackson Avenue | 143rd Street/Third Avenue upper level (demolished) (tied to IRT T) | South Ferry elevated station (demolished) |
| H | Third Avenue Line over Webster Avenue (before 1955 resignalling project) | Gun Hill Road lower level (demolished) | Fordham Road (tied to IRT T) | |
| J | Jerome Avenue Line | Woodlawn | 125th Street/Lexington Avenue (ties to IRT L) | Park Avenue/38th Street |
| K | Broadway-Seventh Avenue Line / Clark Street Tunnel | Chambers Street (ties to IRT V') | Borough Hall | Broadway/44th Street |
| L | Lexington Avenue Line | 125th Street/Lexington Avenue | 42nd Street–Grand Central | Park Avenue/38th Street |
| M | Lexington Avenue Line / Joralemon Street Tunnel | Brooklyn Bridge–City Hall | Borough Hall | Brooklyn Bridge–City Hall |
| MM | 42nd Street Shuttle / Lexington Avenue Line | Times Square | Brooklyn Bridge–City Hall | |
| MV | South Ferry loop | Rector Street | 96th Street (ties to IRT V) | |
| N | Ninth Avenue Line (demolished) | 155th Street | South Ferry elevated station (demolished) | |
| P | Pelham Line | Pelham Bay Park | 125th Street/Lexington Avenue (ties to IRT L) | Park Avenue/38th Street |
| Q | Queensboro Bridge | 57th Street/Second Avenue (tied to IRT S) | Queensboro Plaza | South Ferry elevated station (demolished) |
| R | 162nd Street Connection (from Jerome Avenue Line to Ninth Avenue Line, demolished) | River Avenue/162nd Street | Putnam Bridge | U.S. Bulk Head Line on east shore of the Harlem River |
| S | Second Avenue Line (demolished) | 129th Street | South Ferry elevated station (demolished) | |
| T | Third Avenue Line (demolished) | Bronx Park Terminal | ||
| T | Third Avenue Line over Webster Avenue (after 1955 resignalling project) | Gun Hill Road lower level | Fordham Road | South Ferry elevated station (demolished) |
| V | Broadway-Seventh Avenue Line | Times Square–42nd Street | Rector Street | Broadway/44th Street |
| W | White Plains Road Line | Wakefield–241st Street | West Farms Square–East Tremont Avenue (ties to IRT F) | 96th Street |
| Y | Steinway (now C) | Times Sq | Queensboro Plaza | IRT-7 |
| Y | Dyre Avenue Line | Dyre Avenue | East 180th Street | Oak Point Yard |
| Z | Sixth Avenue Line (demolished) | 53rd Street/Ninth Avenue | Rector Street (tied to IRT N) | South Ferry elevated station (demolished) |
| ZA | 59th Street/Sixth Avenue | 53rd Street/Sixth Avenue | ||
External links
[http://encycl.opentopia.com/ edit ] New York City Subway ([official site])
| |
| Services | 1 2 3 4 5 6 7 A B C D E F G J L M N Q R V W Z |
| Shuttles (S) | 42nd Street • Franklin Avenue • Rockaway Park |
| Unused/defunct | 8 9 10 11 12 13 H K NX P T U X Y • JFK Express BMT: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Shuttles: 63rd Street • Bowling Green • Culver • Grand Street • Other |
| Divisions | IRT • BMT • IND (Second System) |
| Lists | Inter-division connections • Inter-division transfers • Lines • Services • Stations • Terminals • Yards |
| Miscellaneous | Accessibility • Chaining • Dual Contracts • History • Nomenclature • Rolling stock |
| Other transit in NYC | AirTrain JFK • Amtrak • LIRR • Metro-North • NJ Transit • PATH • Roosevelt Island Tramway • Staten Island Railway |
From Wikipedia, the Free Encyclopedia. Original article here. Support Wikipedia by contributing or donating.
All text is available under the terms of the GNU Free Documentation License See Wikipedia Copyrights for details.